GoControl WS15Z5-1 Z-Wave(R) Wall Switch User Manual

Uvod

Thank you for choosing the GoControl WS15Z5-1 Z-Wave Wall Switch. This smart switch allows you to control your lighting or other connected loads remotely via a Z-Wave network, as well as manually. It integrates seamlessly into your smart home system, providing convenience and energy efficiency. Please read this manual carefully before installation and operation to ensure proper use and safety.

Sigurnosne informacije

UPOZORENJE: Risk of Electric Shock. Installation should be performed by a qualified electrician. Disconnect power at the circuit breaker or fuse box before installation or servicing. Use only copper wire for connections. Do not exceed the maximum load ratings.

• Ensure power is OFF at the circuit breaker before installation.
• Ovaj uređaj je namijenjen za instalaciju u skladu s nacionalnim električnim kodeksom i lokalnim propisima.
• Ne koristiti na vlažnim mjestima ili tamo gdje je izravno izložen vodi.
• Samo za unutarnju upotrebu.

Sadržaj paketa

• GoControl WS15Z5-1 Z-Wave Wall Switch
• Instalacijski vijci
• Žičane matice (mogu se razlikovati ovisno o pakiranju)
• Korisnički priručnik (ovaj dokument)

Postavljanje i instalacija

Follow these steps carefully to install your GoControl Z-Wave Wall Switch.

1. Wiring the Switch

1. Isključite napajanje: Locate the circuit breaker controlling the switch you are replacing and turn it OFF. Verify power is off by attempting to turn on the light or appliance.
2. Uklonite stari prekidač: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal (Line, Load, Neutral, Ground).
3. Identificirajte žice:
   • Linija (vruća): Obično crna, dolazi iz prekidača.
   • Opterećenje: Usually black, going to the light fixture or appliance.
   • Neutralno: Usually white, often bundled together in the back of the box. (Required for Z-Wave switches).
   • teren: Obično zeleni ili goli bakar.
4. Spoji novi prekidač: Connect the wires to the GoControl WS15Z5-1 switch terminals as follows:
   • Spojite Linija wire to the terminal marked "LINE".
   • Spojite Opterećenje wire to the terminal marked "LOAD".
   • Spojite Neutralan wire to the terminal marked "NEUTRAL".
   • Spojite Ground wire to the terminal marked "GROUND".

   Provjerite jesu li svi spojevi sigurni. Ako niste sigurni u vezi ožičenja, obratite se kvalificiranom električaru.

5. Prekidač za montažu: Pažljivo gurnite žičani prekidač u zidnu kutiju. Pričvrstite ga priloženim vijcima.
6. Postavite zidnu ploču: Pričvrstite novu ili postojeću zidnu ploču.
7. Vrati snagu: Ponovno uključite napajanje na prekidaču.

Slika 1: Prednja strana view of the GoControl WS15Z5-1 Z-Wave Wall Switch.

2. Z-Wave Inclusion (Pairing)

To integrate the switch into your Z-Wave network, you need to "include" it with your Z-Wave controller.

1. Put your Z-Wave controller into Inclusion/Pairing mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle jednom. The LED indicator on the switch will blink to confirm inclusion mode.
3. The controller will confirm successful inclusion. The switch's LED will stop blinking and remain solid or turn off, depending on its status.
4. If inclusion fails, refer to the Troubleshooting section or try "Exclusion" first.

Figure 2: The Z-Wave logo, indicating compatibility with Z-Wave networks.

Rukovanje prekidačem

Ručna kontrola

• Pritisnite tipku vrh of the paddle to turn the connected load ON.
• Pritisnite tipku dno of the paddle to turn the connected load ISKLJUČENO.

Z-valna kontrola

Once included in your Z-Wave network, you can control the switch remotely using your Z-Wave controller, hub, or compatible smart home application.

• Use your Z-Wave app or controller interface to toggle the switch ON/OFF.
• The switch supports standard Z-Wave commands for basic on/off functionality.

Figure 3: GoControl products integrate with smart home systems for control via smartphones and other devices.

Figure 4: Diagram illustrating GoControl's integration across various smart home categories like Climate, Lighting, Security, Sensors, and Access.

Održavanje

The GoControl WS15Z5-1 Z-Wave Wall Switch requires minimal maintenance.

• Čišćenje: Za čišćenje prekidača, obrišite ga mekom krpomamp tkanina. Nemojte koristiti abrazivna sredstva za čišćenje ili otapala.
• Ažuriranja firmvera: Check the GoControl website or your Z-Wave controller's documentation for information on potential firmware updates.
• Opća njega: Pazite da prekidač nije izložen prekomjernoj vlazi ili ekstremnim temperaturama.

Rješavanje problema

Z-Wave Exclusion (Removing from Network)

If you need to remove the switch from your Z-Wave network, follow these steps:

1. Put your Z-Wave controller into Exclusion mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle jednom. The LED indicator will blink to confirm exclusion mode.
3. The controller will confirm successful exclusion. The switch's LED will stop blinking.

Tehnički podaci

Jamstvo i podrška

GoControl products are designed for reliability and performance. For warranty information, technical support, or further assistance, please visit the official GoControl webstranici ili se obratite njihovom odjelu korisničke službe.

Webstranica: www.gocontrol.com

Proizvođač: GOCONTROL