Surecom SW-33 Mark II Digital VHF/UHF Power & SWR Meter Instruction Manual

1. Uvod

This manual provides detailed instructions for the operation and maintenance of your Surecom SW-33 Mark II Mini Digital VHF UHF Two-Way Radio Handheld Power & SWR Meter. This device is designed to accurately measure the forward power, reverse power, and Standing Wave Ratio (SWR) of your VHF and UHF radio systems. Proper use ensures optimal performance and longevity of your equipment.

2. Sadržaj paketa

Molimo provjerite jesu li svi dolje navedeni artikli uključeni u vaš paket:

• 1x Surecom SW-33 Mark II Digital Power & SWR Meter
• 1x SMA Dummy Load
• 1x USB kabel za punjenje
• 1x Engleski korisnički priručnik
• Various SMA adapters for compatibility

Figure 2.1: A complete view svih stavki uključenih u paket proizvoda.

3. Proizvod je gotovview

The Surecom SW-33 Mark II is a compact and robust device designed for ease of use. It features a clear digital display and intuitive controls.

3.1 Fizičke komponente

• Top Connector: Used for connecting antennas or dummy loads.
• Donji priključak: Used for connecting to your radio device.
• Gumb za napajanje: Located on the front, used to turn the device on/off and cycle through display modes.
• Micro-USB priključak: Located on the top, used for charging the internal battery.
• LED indikator: Next to the Micro-USB port, indicates charging status (red for charging, green for fully charged).
• Digitalni prikaz: Shows SWR, Forward Power (FW), and Reverse Power (RW) values.

Figure 3.1: Detailed diagram highlighting the main components and connection points of the SW-33 Mark II.

Figure 3.2: An illustration of the meter's display, indicating how power and SWR values are presented.

3.2 Initial Power-On Display

Upon startup, the meter's digital display will show three sets of values: SWR, Forward Power (FW), and Reverse Power (RW). You can cycle through these displays by briefly pressing the power button.

4. Postavljanje

4.1 Punjenje uređaja

1. Locate the Micro-USB charging port on the top of the meter.
2. Connect the provided USB charge cable to the meter and a suitable 5V USB power source.
3. The LED indicator next to the port will illuminate red while charging.
4. LED indikator će postati zelen kada je baterija potpuno napunjena.

Figure 4.1: The meter being charged via its convenient Micro USB port.

4.2 Uključivanje/isključivanje

To power on the device, press and hold the power button for a few seconds until the display illuminates. To power off, press and hold the power button again until the display turns off.

5. Operating Instructions: Power Measurement

Follow these steps to measure the RF power output of your radio device:

1. Ensure the meter is adequately charged.
2. Connect your radio device to the bottom connector of the SW-33 Mark II. Use appropriate adapters if necessary (included in the package).
3. Connect a suitable dummy load to the top connector of the SW-33 Mark II. Ensure the dummy load can handle the maximum power output of your radio.
4. Power on the SW-33 Mark II. Press the power button until the indicator light is at the top left, displaying FW (Forward Power) values.
5. Hold down the Push-To-Talk (PTT) button on your radio for a few seconds.
6. Observe the FW value on the meter's display. This indicates the forward power output of your radio.

Figure 5.1: Visual guide demonstrating the correct setup for measuring the transmit power of a two-way radio.

6. Operating Instructions: SWR Measurement

Follow these steps to measure the SWR of your antenna:

1. Ensure the meter is adequately charged.
2. Connect your radio device to the bottom connector of the SW-33 Mark II. Use appropriate adapters if necessary.
3. Connect the antenna you wish to test to the top connector of the SW-33 Mark II. Ensure the antenna is positioned vertically and there are no obstructions nearby.
4. Power on the SW-33 Mark II. Press the power button until the indicator light is at the middle left, displaying SWR values.
5. It is recommended to test with your radio device set to high power for more accurate results.
6. Hold the meter steadily and hold down the Push-To-Talk (PTT) button on your radio for a few seconds.
7. Observe the SWR value on the meter's display. An SWR value closer to 1.0 indicates better antenna performance and a good match.

Figure 6.1: Visual guide demonstrating the correct setup for measuring the Standing Wave Ratio (SWR) of an antenna.

7. Specifikacije

8. Održavanje

• Čišćenje: Za čišćenje vanjske strane uređaja koristite meku, suhu krpu. Nemojte koristiti jake kemikalije ili abrazivna sredstva za čišćenje.
• Skladištenje: Mjerač čuvajte na hladnom i suhom mjestu, dalje od izravne sunčeve svjetlosti i ekstremnih temperatura.
• Njega baterije: For optimal battery life, avoid fully discharging the battery frequently. Recharge the device regularly, especially if it will not be used for an extended period.
• Priključci: Keep connectors clean and free from dust or debris to ensure reliable connections.

9. Rješavanje problema

10. Jamstvo i podrška

Za informacije o jamstvu ili tehničku podršku, molimo pogledajte dokumentaciju koja je priložena uz kupnju ili se izravno obratite prodavatelju. Sačuvajte dokaz o kupnji za bilo kakve reklamacije u okviru jamstva.