SABRENT M.2 NVMe SSD to PCIe Adapter Card (EC-PCIE) Instruction Manual

1. Uvod

This manual provides detailed instructions for the installation and use of the SABRENT M.2 NVMe SSD to PCIe Adapter Card (EC-PCIE). This adapter allows you to add an M.2 NVMe Solid State Drive to your desktop computer via an available PCIe slot, enhancing storage performance and capacity.

2. Sadržaj paketa

• NVMe M.2 SSD to PCIe x16/x8/x4 Adapter Card (SSD not included)
• Aluminum Heatsink with Thermal Pad
• Odvijač
• Necessary Screws

Image: The adapter card, heatsink, thermal pads, and screwdriver included in the package.

3. Kompatibilnost

• Supported SSDs: M.2 NVMe SSDs in sizes 2230, 2242, 2260, and 2280.
• Supported PCIe Slots: PCIe x16, x8, and x4 physical slots.
• Nekompatibilno: Not compatible with M.2 SATA SSDs (B-Key or B+M Key) or PCIe x1 slots.
• Zahtjevi sustava: Windows 7 (with NVMe hotfix), Windows 8/10/11, or Linux. Motherboard BIOS must support NVMe drives over PCIe lanes.

Image: Visual representation of compatible M-Key NVMe SSDs and incompatible B&M-Key SATA SSDs.

Image: Illustration of PCIe slot compatibility, indicating support for x16, x8, and x4 slots, but not x1 slots.

4. Postavljanje i instalacija

4.1. Installing the M.2 NVMe SSD into the Adapter

1. Unscrew the four small screws on the back panel of the adapter using the provided screwdriver. Carefully remove the back panel.
2. Locate the small fastening screw inside the adapter. This screw holds the M.2 SSD in place. Unscrew it by about half a turn to loosen it. This screw can be relocated to different holes to accommodate various M.2 SSD lengths (2230, 2242, 2260, 2280). Adjust its position if necessary for your SSD size.
3. Carefully insert your M.2 NVMe SSD into the M.2 slot on the adapter at a 45-degree angle.
4. Gently push the SSD down until it is flat against the adapter board. Secure it by tightening the small fastening screw. Do not overtighten.
5. Peel off one side of the protective film from the thermal pad and place it onto the NVMe SSD. Smooth it out to ensure good contact. Then, remove the remaining protective film.
6. Place the aluminum heatsink over the SSD, ensuring it aligns with the thermal pad.
7. Reattach the back panel and secure it with the four small screws.

Image: Step-by-step illustration of inserting the M.2 NVMe SSD into the adapter and securing it.

4.2. Installing the Adapter Card into a PCIe Slot

1. Isključite računalo i odspojite sve kabele. Otvorite kućište računala.
2. Locate an available PCIe x4, x8, or x16 slot on your motherboard. Consult your motherboard's manual to identify suitable slots and ensure they support NVMe functionality.
3. Remove any bracket covers from the chosen PCIe slot on your computer case.
4. Align the adapter card with the PCIe slot. Gently push the adapter card down into the slot until it is fully seated and you hear a click, indicating it is locked in place.
5. Secure the adapter card to the computer case with a screw if your case provides a mounting point.
6. Zatvorite kućište računala, ponovno spojite sve kabele i uključite računalo.

5. Upute za rad

Once installed, your operating system should detect the new NVMe SSD. You may need to initialize and format the drive through your operating system's disk management utility before it can be used for storage. Refer to your operating system's documentation for instructions on disk management.

The adapter facilitates high-speed data transfer over the PCIe lanes, allowing your NVMe SSD to operate at its optimal performance, provided the motherboard's PCIe slot supports the required bandwidth (e.g., PCIe Gen4 for Gen4 NVMe SSDs).

6. Održavanje

The included aluminum heatsink and thermal pad are designed to dissipate heat from the NVMe SSD, ensuring stable performance and longevity. No specific ongoing maintenance is required beyond ensuring proper airflow within your computer case.

Image: Visual representation of the heat dissipation design, highlighting how the heatsink helps cool the SSD.

7. Rješavanje problema

• SSD nije otkriven:
  • Ensure the M.2 NVMe SSD is correctly seated in the adapter and the adapter is fully seated in the PCIe slot.
  • Verify that your motherboard's BIOS/UEFI settings are configured to support NVMe drives via PCIe. Some motherboards may require specific settings to be enabled.
  • Check your motherboard's manual for any shared bandwidth limitations between PCIe slots and M.2 slots.
  • Ensure the SSD is an M-Key NVMe type, not a B-Key or B+M Key SATA SSD.
• Spora izvedba:
  • Confirm that the PCIe slot used provides sufficient bandwidth for your NVMe SSD (e.g., a PCIe Gen4 SSD should ideally be in a Gen4 slot). Using a higher generation SSD in a lower generation PCIe slot will limit its speed to the lower generation's capabilities.
  • Ensure the PCIe slot is operating in x4 mode or higher, as required by the NVMe standard for optimal performance.

8. Specifikacije

9. Jamstvo

This product is backed by SABRENT's 1-year warranty. Please refer to the official SABRENT webstranicu za detaljne uvjete jamstva.