KICKER 48TRTP122 Subwoofer and DS18 CANDY-X1B AmpKorisnički priručnik za sustav lifier

1. Proizvod je gotovview

This manual provides instructions for the KICKER 48TRTP122 12-inch CompRT Down-Firing Loaded Subwoofer Enclosure, the DS18 CANDY-X1B Mono Class D Amplifier, and the accompanying DS18 AMPKIT4 4AWG Complete Amplifier Wiring Kit. This system is designed to enhance your vehicle's audio experience with powerful bass output.

2. Što je u kutiji

• Kicker 48TRTP122 12" CompRT Series Down-Firing Loaded Subwoofer Enclosure
• DS18 CANDY-X1B Mono Candy-X Series Car Amplifter
• DS18 AMPKIT4 4AWG Complete Amplifier Kit, including:
  • 17 ft 4 AWG Red Power Wire
  • 3 ft 4 AWG Black Ground Wire
  • 17 ft Remote Wire
  • 17 ft Red/Black Speaker Cable
  • 17 ft Red/Black Twisted RCA Cable
  • Mini ANL Fuse Holder with Mini ANL 100A Fuse
  • 6 ft 4 AWG Loom Tube
  • 1 x Rubber Grommet
  • 10 x vezice za kablove
  • 2 x prstenasti terminali
  • 2 x Spade Terminali
  • 5 x Small Spade Terminals

Figure 2.1: Components of the DS18 AMPKIT4 4AWG Complete AmpLifier Kit.

3. Postavljanje i instalacija

Pravilna instalacija ključna je za optimalne performanse i sigurnost. Ako niste sigurni u vezi s bilo kojim koracima, obratite se profesionalnom instalateru auto audio sustava.

3.1 Sigurnosne mjere opreza

• Prije početka bilo kakvih električnih radova odspojite negativni pol akumulatora vozila.
• Provjerite jesu li sve žice pravilno izolirane i osigurane kako biste spriječili kratki spoj i oštećenje.
• Tijekom instalacije koristite odgovarajuću osobnu zaštitnu opremu (OZO).

3.2 Subwoofer Enclosure Placement

The KICKER 48TRTP122 is a down-firing enclosure, designed to be placed in the trunk or cargo area of your vehicle. Ensure it is securely fastened to prevent movement during driving.

Figure 3.1: KICKER 48TRTP122 Down-Firing Subwoofer Enclosure.

3.3 AmpLifier Montaža

Mount the DS18 CANDY-X1B amplifier in a location that allows for adequate ventilation and protection from moisture. Common locations include under a seat, in the trunk, or on the back of a rear seat. Ensure it is securely mounted to prevent vibration damage.

Figure 3.2: DS18 CANDY-X1B Mono Class D Ampsredstvo za podsticanje.

3.4 Upute za ožičenje

Follow these steps carefully for wiring the system. Refer to the wiring diagram below for visual guidance.

1. Power Wire (Red 4 AWG): Run the 17 ft red power wire from the vehicle's positive battery terminal to the fuse holder, then from the fuse holder to the +12V terminal on the DS18 amplifier. Ensure the fuse holder is installed close to the battery (within 18 inches).
2. Ground Wire (Black 4 AWG): Connect the 3 ft black ground wire from the GND terminal on the ampPričvrstite gornji dio na čistu, neobojenu metalnu površinu na šasiji vozila. Osigurajte dobru električnu vezu.
3. Žica za daljinsko uključivanje: Connect the remote wire from your head unit's remote output to the REM terminal on the ampzaštitno sredstvo. Ova žica okreće ampuključivanje i isključivanje plamenika pomoću vaše glavne jedinice.
4. RCA kablovi: Connect the RCA cables from your head unit's subwoofer output (or full-range output if no dedicated sub output) to the RCA input jacks on the DS18 ampsredstvo za podsticanje.
5. Žica zvučnika: Spojite kabel zvučnika iz amplifier's speaker output terminals to the KICKER subwoofer enclosure's input terminals. Ensure correct polarity (+ to + and - to -). The KICKER 48TRTP122 enclosure has a 2-ohm impedance.
6. Bas daljinski: Connect the included bass remote to the dedicated remote port on the DS18 amplifier. Mount the remote in an accessible location for easy adjustment.

Figure 3.3: Subwoofer to Amplifier Wiring Diagram (2-ohm connection).

Figure 3.4: DS18 Bass Remote Control.

4. Upute za rad

Once the system is installed, follow these steps to configure and operate your subwoofer and ampsredstvo za podsticanje.

4.1 Initial Power-Up and Gain Setting

1. Ponovno spojite negativni pol akumulatora vozila.
2. Uključite glavnu jedinicu. amplifier should power on (indicated by a blue LED on the amplifier).
3. Postavite amplifier's GAIN control to its minimum (fully counter-clockwise) position.
4. Play a music track with strong bass at a moderate volume level on your head unit (around 75% of maximum volume).
5. Polako povećavajte kontrolu GAIN na amplifier until you hear distortion, then back it off slightly until the sound is clear. This sets the maximum clean output level.

4.2 Amplifier Controls (DS18 CANDY-X1B)

The DS18 CANDY-X1B amplifier features several controls for fine-tuning your bass output:

• DOBITAK: Adjusts the input sensitivity to match the output of your head unit. (See 4.1)
• BASS BOOST (0-18 dB): Increases the bass output at a specific frequency (typically around 45 Hz). Use sparingly to avoid distortion and speaker damage.
• LPF (Low-Pass Filter) (50-150 Hz): This filter allows only frequencies below the set point to pass through to the subwoofer. Adjust to blend the subwoofer's output seamlessly with your main speakers.
• SUBSONIC FILTER (10-55 Hz): Filters out extremely low frequencies that are inaudible and can cause damage to the subwoofer. Set it slightly below your subwoofer's lowest usable frequency.
• PHASE (0/180 degrees): Adjusts the phase of the subwoofer output relative to your main speakers. Experiment with both settings to find the one that provides the most impactful and coherent bass.
• DALJINSKI: Port for connecting the wired bass remote control, allowing convenient bass level adjustment from the driver's seat.

Figure 4.1: DS18 CANDY-X1B Amplifier Controls.

5. Održavanje

Regular maintenance ensures the longevity and optimal performance of your audio system.

• Čišćenje: Držite kućište subwoofera i amplifier clean and free of dust and debris. Use a soft, dry cloth. Avoid liquid cleaners directly on components.
• Veze: Povremeno provjeravajte sve spojeve ožičenja na čvrstoću i koroziju. Labavi spojevi mogu dovesti do loših performansi ili oštećenja.
• Ventilacija: Osigurajte amplifier's cooling fins are not obstructed to prevent overheating.
• Provjera osigurača: Ako je amplifier does not power on, check the fuse in the fuse holder near the battery. Replace with a fuse of the same rating (100A Mini ANL).

6. Rješavanje problema

U ovom odjeljku potražite uobičajene probleme i njihova rješenja.

7. Specifikacije

Detailed specifications for the components in this bundle.

7.1 KICKER 48TRTP122 12" CompRT Subwoofer Enclosure

• Vrsta zvučnika: Subwoofer
• Promjer subwoofera: 12 inča
• Vršna snaga: 1000 vata
• RMS snaga: 500 vata
• Impedancija: 2 oma
• Osjetljivost: 98 dB
• Posebna značajka: Down-Firing, Active thin-mount CompRT subwoofer, High-output reFLEX passive woofer
• Materijal: Vlaknaste ploče srednje gustoće
• Dimenzije: 27.5" W x 6.125" H x 14.625" D (Top) x 14.625" D (Bottom)

7.2 DS18 CANDY-X1B Mono Class D Amplifter

• RMS snaga:
  • 4 ohms: 240 watts x 1 channel
  • 2 ohms: 400 watts x 1 channel
  • 1 ohm: 600 watts x 1 channel
• Maksimalna izlazna snaga: 1800 vata
• Osjetljivost: 100 dB
• Frekvencijski odziv: 20-150 Hz
• Bas daljinski: Uključeno
• Dizajn: Klasa D
• Varijabilno pojačanje basa: 0-18 dB
• Variable Low-pass filter (LPF): 50-150 Hz
• Podzvučni filter: 10-55 Hz
• Dimenzije: 5.9 cm Š x 8.3 cm D x 2.16 cm V

7.3 DS18 AMPKIT4 4AWG Complete AmpLifier Kit

• Mjerač žice: 4 AWG
• Materijal žice: High Performance CCA (Copper Clad Aluminum)
• Preporučeno za: Jedan amplifier up to 1300 Watts
• Uključene komponente: Power wire, ground wire, remote wire, speaker cable, RCA cable, fuse holder with 100A fuse, loom tube, grommet, cable ties, various terminals.

8. Informacije o jamstvu

This product bundle typically comes with a manufacturer's warranty. The KICKER 48TRTP122 subwoofer enclosure and DS18 CANDY-X1B amplifier are covered by a full warranty from their respective manufacturers. Specific warranty terms, duration, and coverage details may vary. Please retain your proof of purchase for warranty claims.

For detailed warranty information, refer to the documentation included with each individual component or visit the respective manufacturer's official webmjesto.

9. Podrška

If you encounter issues not covered in this manual or require further assistance, please contact the manufacturer's customer support:

• KICKER Support: Visit the official KICKER webstranica za resurse podrške, često postavljana pitanja i kontakt informacije.
• DS18 Support: Posjetite službeni DS18 website for product support and contact details.

When contacting support, please have your product model numbers (48TRTP122, CANDY-X1B, AMPKIT4) and proof of purchase readily available.