1. Uvod
Thank you for choosing the Wiltec 1200W Submersible Water Pump. This manual provides essential information for the safe and efficient operation, installation, and maintenance of your pump. Please read these instructions carefully before use and retain them for future reference.
This submersible pump is designed for pumping water from wells, tanks, and other water sources. It features a powerful 1200W motor, a maximum flow rate of 6000 L/h, a maximum discharge height of 40 meters, and an immersion depth of up to 12 meters. Integrated safety features include a float switch, dry-run protection, and a thermoregulator to ensure reliable performance and longevity.
2. Sigurnosne upute
UPOZORENJE: Nepoštivanje ovih sigurnosnih uputa može uzrokovati strujni udar, požar, teške ozljede ili smrt.
- Uvijek isključite pumpu iz napajanja prije bilo kakvog održavanja, čišćenja ili kada se ne koristi.
- Provjerite je li napajanje voltage matches the specifications on the pump's rating label.
- Do not operate the pump with a damaged power cord or plug. If damaged, it must be replaced by the manufacturer, service agent, or similarly qualified persons to avoid a hazard.
- Never lift or carry the pump by its power cord. Use the designated handle or a sturdy rope attached to the pump's lifting eye.
- Držite djecu i neovlaštene osobe podalje od radnog područja.
- The pump is designed for pumping clean water. Do not use it for flammable, corrosive, or explosive liquids.
- Ensure the pump is fully submerged during operation to prevent dry running, which can cause damage. The integrated dry-run detector provides additional protection.
- Do not operate the pump in swimming pools or areas where people are in the water.
- Protect the pump from frost. Drain all water from the pump and hoses if there is a risk of freezing temperatures.
- The built-in thermoregulator protects the motor from overheating. If the pump shuts off automatically, allow it to cool down before restarting.
3. Proizvod je gotovview
The Wiltec 1200W Submersible Water Pump is constructed with a durable plastic and stainless steel main body, ensuring corrosion resistance and portability. It features a robust motor and advanced safety mechanisms for reliable water transfer.
Slika 3.1: A person lowering the Wiltec Submersible Water Pump into a body of water. The image highlights the pump's capability to achieve a 40-meter discharge height and its general use as a submersible pump.
Slika 3.2: Detaljan view of the Wiltec Submersible Water Pump, showcasing njegova robusna crna casing, integrated handle, and the float switch mechanism attached to the side.
4. Specifikacije
Refer to the table below for detailed technical specifications of the Wiltec 1200W Submersible Water Pump.
Slika 4.1: This diagram illustrates the product dimensions (500mm height, 165mm diameter) and key performance data, including a 10m cable length and a performance curve showing flow rate versus discharge height.
| Značajka | Specifikacija |
|---|---|
| Broj modela | 65343 |
| Vlast | 1200 W |
| Maks. Protok | 6000 L/h |
| Max. Discharge Height | 40 m |
| Maks. Dubina uranjanja | 12 m |
| Duljina kabela | 10 m |
| Maks. Veličina čestica | 1 mm |
| Min. Water Level for Suction | 34 mm |
| Vrsta zaštite | IPX8 |
| Materijal | Plastic (Polypropylene), Stainless Steel |
| Težina artikla | 9 kg |
| Raspon radne temperature | 1°C - 35°C |
5. Postavljanje i instalacija
5.1 Spajanje ispusnog crijeva
The pump is compatible with various hose diameters. Ensure a secure connection to prevent leaks and maintain optimal flow.
Slika 5.1: This image illustrates the pump's compatibility with different hose diameters, specifically 31mm and 25mm, and shows the necessary adapters for connection.
- Select a discharge hose of appropriate diameter (e.g., 25mm or 31mm) for your application.
- Attach the hose connector to the pump's discharge outlet.
- Secure the hose to the connector using a hose clamp (not included) to ensure a watertight seal.
- Position the discharge end of the hose to direct water to the desired location.
5.2 Postavljanje pumpe
- Lower the pump into the water source using a sturdy rope attached to the pump's lifting eye. Do not use the power cable.
- Ensure the pump is placed on a stable, level surface at the bottom of the water source, or suspended so it does not rest directly on sediment.
- The pump must be fully submerged during operation. The maximum immersion depth is 12 meters.
- Ensure the float switch has sufficient space to move freely and activate/deactivate the pump based on water levels.
6. Upute za rad
6.1 Priključak za napajanje
Once the pump is correctly positioned and the discharge hose is connected, plug the pump into a grounded electrical outlet. Ensure the outlet is protected by a Residual Current Device (RCD) for safety.
6.2 Automatski rad (plovak)
The pump is equipped with a float switch for automatic operation. When the water level rises, the float switch will lift, turning the pump on. As the water level drops, the float switch will lower, turning the pump off. Adjust the float switch cable length to set the desired on/off water levels.
Slika 6.1: This graphic depicts the two operating modes: 'Smart Sensor' (automatic via float switch) and 'Manual Operation', showing the float switch mechanism.
6.3 Ručni rad
For continuous pumping, the float switch can be secured in an upward position. This will keep the pump running regardless of the water level. Oprez: When operating in manual mode, closely monitor the water level to prevent dry running, which can damage the pump. The dry-run detector will provide protection, but manual oversight is recommended.
6.4 Dry-Run Protection and Thermoregulator
The pump features a dry-run detector that automatically shuts off the pump if the water level becomes too low, preventing damage. Additionally, a built-in thermoregulator protects the motor from overheating. If the pump stops unexpectedly, allow it to cool down for approximately 15-20 minutes before attempting to restart it.
Slika 6.2: This image highlights the pump's efficient water suction capability, processing particles up to 1mm, and indicates a minimum water level of 34mm for operation.
7. Održavanje
Regular maintenance ensures the longevity and optimal performance of your Wiltec submersible pump.
7.1 Čišćenje
- Before cleaning, always disconnect the pump from the power supply.
- Rinse the pump with clean water after each use, especially if pumping dirty water, to prevent sediment buildup.
- Inspect the intake screen for blockages. Remove any debris carefully.
- Check the float switch for free movement and clean any obstructions.
7.2 Skladištenje
- If the pump will not be used for an extended period, or during freezing temperatures, drain all water from the pump and hoses.
- Pumpu čuvajte na suhom mjestu, zaštićenom od smrzavanja.
- Coil the power cable neatly to prevent damage.
8. Rješavanje problema
This section provides solutions to common problems you might encounter with your submersible pump.
| Problem | Mogući uzrok | Otopina |
|---|---|---|
| Pumpa se ne pokreće | Nema napajanja Plovni prekidač nije aktiviran Aktivirana zaštita od pregrijavanja Radno kolo blokirano | Provjerite priključak za napajanje i osigurač Ensure float switch is free to move and in 'ON' position Allow pump to cool down (approx. 15-20 min) Disconnect power, clean intake screen and impeller |
| Pumpa radi, ali voda se ne ispušta ili je protok nizak | Air in pump/hose Ispusno crijevo je savijeno ili začepljeno Začepljen usisni filter Razina vode preniska Pumpa nije potpuno uronjena | Ensure pump is fully submerged and allow air to escape Provjerite i očistite crijevo Isključite napajanje, očistite usisnu mrežicu Ensure water level is above minimum operating level Reposition pump to ensure full submersion |
| Pumpa se zaustavlja tijekom rada | Aktivirana zaštita od pregrijavanja Dry-run protection activated Float switch deactivated (water level too low) | Allow pump to cool down Check water level, ensure pump is submerged Check water level, adjust float switch if necessary |
| Pretjerana buka ili vibracija | Pumpa nije stabilna Impeller damaged or blocked | Osigurajte da je pumpa na stabilnoj površini Isključite napajanje, pregledajte i očistite impeler |
9. Svestrane primjene
The Wiltec 1200W Submersible Water Pump is suitable for a wide range of water transfer tasks, making it a versatile tool for both domestic and professional use.
Slika 9.1: This image displays several common applications for the pump, including emptying a rain barrel, garden irrigation, maintaining a garden pond, and dewatering a flooded cellar.
- Dewatering: Quickly remove water from flooded basements, construction sites, or other areas.
- Navodnjavanje vrta: Utilize water from rain barrels, ponds, or wells for watering gardens and lawns.
- Održavanje ribnjaka: Circulate or empty water from garden ponds.
- Prijenos vode: Move water between tanks, containers, or other sources.
10. Jamstvo i podrška
For warranty information, technical support, or spare parts, please contact Wiltec customer service or refer to the purchase documentation. Keep your proof of purchase for any warranty claims.