1. Uvod
This manual provides essential information for the installation, operation, and maintenance of your FACULX 36/48V 35A 1500W Ebike Brushless Motor Controller. This controller is designed for electric bicycles, offering efficient power management for brushless motors and compatibility with various LCD displays (LCD3, LCD4, LCD5, LCD7). Please read this manual thoroughly before installation and use to ensure proper function and safety.
2. Sigurnosne informacije
- Always disconnect the battery before performing any installation, maintenance, or repair work on the ebike electrical system.
- Ensure all connections are secure and correctly polarized to prevent damage to the controller or other components.
- Avoid exposing the controller to water, excessive moisture, or extreme temperatures.
- Ne pokušavajte otvarati ili modificirati kontroler casing. This may void the warranty and pose a safety risk.
- Consult a qualified technician if you are unsure about any installation steps or encounter persistent issues.
3. Sadržaj paketa
Provjerite jesu li svi artikli prisutni u vašem paketu:
- FACULX 36/48V 35A 1500W Ebike Brushless Motor Controller (Model: 36/48KSRL-FF01) with integrated wiring harness.
Slika 3.1: Gotovoview of the FACULX Ebike Brushless Motor Controller with its integrated wiring harness.
4. Postavljanje i instalacija
Follow these steps to correctly install your ebike controller. Ensure the battery is disconnected before starting.
4.1. Controller Mounting
Mount the controller securely to your ebike frame in a location protected from physical impact and moisture. Use appropriate fasteners (not included) to ensure it is stable during operation.
4.2. Spajanje ožičenja
Identify each connector on the controller's wiring harness and connect them to the corresponding components on your ebike. Refer to the images below for visual guidance.
- Spajanje baterije: Connect the main power cables (typically red for positive, black for negative) to your ebike battery. Ensure correct polarity. This controller uses a common XT60 or similar high-current connector for the battery.
- Fazne žice motora: Connect the three thick phase wires (usually green, blue, yellow) from the controller to the corresponding phase wires of your brushless motor.
- Žice Hallovog senzora: Connect the smaller Hall sensor wire bundle (typically 5 or 6 wires) from the controller to the motor's Hall sensor connector.
- Povezivanje zaslona: Connect the display cable to your compatible LCD3, LCD4, LCD5, or LCD7 display unit. This is often a multi-pin waterproof connector.
- Priključak gasa: Connect the throttle cable to your ebike's throttle unit.
- Brake Lever Connections: Connect the brake lever cables. This controller supports low-level brake input.
- Pedal Assist Sensor (PAS) Connection: If your ebike has a PAS, connect its cable to the controller.
- Ostale veze: Connect any other auxiliary cables such as lights or speed sensors if applicable and supported by your controller model.
Slika 4.1: Detaljno view of the controller's wiring harness, showing different connector types for various ebike components.
Slika 4.2: Primjerample of a multi-pin connector, often used for display or throttle connections.
Slika 4.3: Primjerample of ring terminal connectors, typically used for motor phase wires.
5. Upute za rad
Once the controller is correctly installed and all connections are secure, you can begin operating your ebike.
- Uključivanje: Turn on your ebike battery and then power on your LCD display unit. The display should illuminate and show relevant information.
- Kontrola gasa: Gently twist the throttle to engage the motor. The motor speed will correspond to the throttle input.
- Pomoć pri pedaliranju (PAS): If equipped, begin pedaling, and the PAS system will provide motor assistance based on your pedaling effort and the selected assist level on your display.
- Kočenje: Activating the brake levers will cut off power to the motor, ensuring safe stopping.
- Funkcije prikaza: Use your LCD display to monitor speed, battery level, assist level, and other parameters. Refer to your specific LCD display manual for detailed instructions on its functions.
6. Održavanje
Pravilno održavanje osigurava dugotrajnost i pouzdan rad vašeg regulatora.
- Redoviti pregled: Povremeno provjeravajte sve spojeve ožičenja na čvrstoću i znakove istrošenosti ili oštećenja.
- Čistoća: Keep the controller clean and free from dust, dirt, and debris. Use a dry cloth for cleaning. Do not use water or harsh chemicals.
- Zaštita okoliša: Store and operate your ebike in conditions that protect the controller from extreme weather, direct sunlight, and high humidity.
- Uprava za kabele: Ensure cables are neatly routed and secured to prevent snagging or damage during riding.
7. Rješavanje problema
If you encounter issues with your controller, refer to the following common problems and solutions:
| Problem | Mogući uzrok | Otopina |
|---|---|---|
| Motor ne radi | Loose battery connection, low battery, motor/Hall sensor wires disconnected, faulty throttle/display. | Check battery charge and connections. Verify all motor, Hall sensor, throttle, and display cables are securely connected. |
| Zaslon se ne uključuje | Battery off, display cable loose/damaged, faulty display. | Ensure battery is on. Check display cable connection. Test with a known good display if possible. |
| Motor se povremeno gasi | Loose connections, overheating, low battery voltage. | Inspect all connections. Allow controller to cool down. Check battery voltage. |
| Incorrect speed reading on display | Speed sensor issue, incorrect display settings. | Check speed sensor connection. Verify wheel size and other parameters are correctly set in the display. |
If the problem persists after attempting these solutions, please consult a professional ebike technician.
8. Specifikacije
The following are the technical specifications for the FACULX Ebike Brushless Motor Controller (Model: 36/48KSRL-FF01):
Image 8.1: Controller label displaying key specifications.
- Model: 36/48KSRL-FF01
- Ocijenjeno svtage: DC36V/48V
- Nazivna struja: 17A
- Maksimalna struja: 35±1A
- Speed Set: 1-4.2 V
- Ulaz kočnice: Niska razina
- Niski volumentage Zaštita: DC30/40±0.5 V