APNX V2 ATX Case Instruction Manual

1. Uvod

The APNX V2 ATX Case is designed for high-performance PC builds, featuring an X-Pand Flow Dual Airflow system and extensive compatibility for modern components. This manual provides instructions for assembly, operation, and maintenance to ensure optimal performance and longevity of your system.

Figure 1: APNX V2 ATX Case overview, showcasing its spacious interior and tempered glass panels.

Ključne karakteristike:

• X-Pand Flow Dual Airflow Design: Separates GPU and PSU cooling zones for enhanced thermal performance.
• Premium Cooling Support: Accommodates up to two 160mm and seven 140mm fans, with dual 360mm radiator support. Includes four pre-installed 140mm fans.
• Next-Gen Compatibility: Supports vertical and reverse-layout motherboards, along with modular PSU and HDD trays.
• ARGB Control Hub: A 10-port ARGB PWM hub is included for synchronized lighting and fan management.
• 3-Sided Tempered Glass Panels: Removable front, side, and top glass panels provide a panoramic view i jednostavan pristup.

2. Postavljanje i instalacija

Follow these steps for proper assembly and installation of components within your APNX V2 ATX Case.

2.1 Unpacking and Initial Access

1. Pažljivo izvadite kutiju iz ambalaže.
2. Locate and remove the captive thumb screws securing the top and side tempered glass panels. Gently lift and remove these panels.
3. The front tempered glass panel is secured by four small screws. Remove these screws to detach the front panel for full access.

Slika 2: Stražnji dio view of the APNX V2 case, showing the removable side panel and fan mounting options.

2.2 Instalacija matične ploče

1. Ensure the correct standoffs are installed for your motherboard form factor (ATX, Micro ATX).
2. Carefully place your motherboard into the case, aligning it with the standoffs and I/O shield opening.
3. Pričvrstite matičnu ploču priloženim vijcima.
4. For reverse-layout motherboards, refer to your motherboard's manual for specific installation guidance.

2.3 Instalacija jedinice za napajanje (PSU)

1. The PSU slot can be adjusted to two different locations for optimized cable management. Choose the desired position.
2. Mount the PSU into its designated bay, typically at the bottom rear of the case.
3. Pričvrstite napajanje vijcima sa stražnje strane kućišta.

Figure 3: Internal layout highlighting modular PSU and HDD trays for flexible configuration.

2.4 Cooling System Installation (Fans & Radiators)

1. The case comes with four pre-installed 140mm fans (three bottom intake, one rear exhaust).
2. Additional fans (up to two 160mm and seven 140mm total) can be installed on the top, side, and bottom mounts.
3. Radiators up to 360mm can be mounted on the top and side positions.
4. Connect all fan cables to the included 10-port ARGB PWM hub, then connect the hub to your motherboard's fan and ARGB headers.

Slika 4: View of the case interior showing the bottom intake fans, part of the X-Pand Flow design.

2.5 Instalacija grafičke kartice (GPU)

1. Uklonite potrebne poklopce PCIe utora sa stražnje strane kućišta.
2. Insert your GPU into the PCIe slot on the motherboard and secure it with screws.
3. Utilize the built-in GPU sag bracket to support heavier graphics cards. This bracket is adjustable vertically and horizontally.

2.6 Upravljanje kabelima

• Route cables through the designated cutouts and channels behind the motherboard tray.
• Use the included Velcro straps and cable ties to secure cables neatly.
• The modular PSU and HDD trays also aid in managing cables effectively.

Figure 5: Rear interior view, illustrating the space and features for cable management.

3. Operacija

Understanding the operational aspects of your APNX V2 ATX Case.

3.1 Uključivanje

• Ensure all components are correctly installed and connected.
• Spojite kabel za napajanje na napajanje i zidnu utičnicu.
• Press the power button located on the front I/O panel.

Figure 6: Close-up of the front I/O panel, including power button and USB ports.

3.2 Airflow Management (X-Pand Flow)

The X-Pand Flow design optimizes cooling by separating airflow paths for the GPU and PSU. The pre-installed bottom fans act as intake, directing cool air directly to the GPU, while the rear fan exhausts hot air. Additional fans can be configured to further enhance this airflow.

3.3 ARGB upravljanje rasvjetom

The included 10-port ARGB PWM hub allows for centralized control of your case fans' speed and ARGB lighting. Connect the hub to your motherboard's ARGB header and use your motherboard's software (e.g., ASUS Aura Sync, MSI Mystic Light, Gigabyte RGB Fusion) to customize lighting effects and fan curves.

4. Održavanje

Regular maintenance helps preserve the performance and appearance of your PC case.

4.1 Čišćenje filtera za prašinu

• The APNX V2 case features removable dust filters, typically located at the bottom (under the PSU and intake fans).
• Gently slide out the dust filters.
• Clean the filters using compressed air or by rinsing them with water. Ensure they are completely dry before re-installing.
• Regular cleaning (e.g., monthly) is recommended to maintain optimal airflow and prevent dust buildup.

Figure 7: Close-up of the removable dust filter, demonstrating ease of access for cleaning.

4.2 Tempered Glass Panel Cleaning

• Use a soft, microfiber cloth and a non-abrasive glass cleaner to clean the tempered glass panels.
• Avoid harsh chemicals or abrasive materials that could scratch the glass.
• Ensure the panels are dry before reattaching them to the case.

5. Rješavanje problema

Uobičajeni problemi i njihova moguća rješenja.

5.1 Ventilatori se ne okreću ili ARGB ne svijetli

• Provjerite veze: Ensure all fans are securely connected to the ARGB PWM hub. Verify the hub is connected to both a SATA power connector from the PSU and the appropriate fan/ARGB headers on the motherboard.
• Softver matične ploče: Confirm that your motherboard's fan control and ARGB software is installed and configured correctly.
• Ciklus snage: Turn off your PC, unplug it from the wall, wait 30 seconds, then plug it back in and restart.

5.2 High Component Temperatures

• Nakupljanje prašine: Očistite sve filtere za prašinu i unutarnje komponente kako je opisano u odjeljku Održavanje.
• Konfiguracija ventilatora: Ensure fans are installed with correct airflow direction (intake/exhaust). The bottom fans should be intake, and the rear fan exhaust.
• Uprava za kabele: Poor cable management can obstruct airflow. Re-route cables to minimize obstruction.
• Component Clearance: Verify that large components (e.g., CPU cooler, GPU) are not obstructing critical airflow paths.

5.3 Front I/O Ports Not Functioning

• Unutarnje veze: Check that the front I/O cables (USB, audio, power/reset switches) are correctly connected to the corresponding headers on your motherboard.
• Instalacija upravljačkog programa: Ensure all necessary motherboard drivers, especially for USB controllers, are installed.

6. Specifikacije

7. Jamstvo i podrška

7.1 Informacije o jamstvu

The APNX V2 ATX Case comes with a Ograničeno jamstvo. Please retain your proof of purchase for warranty claims. For specific terms and conditions, refer to the warranty card included with your product or visit the official APNX webmjesto.

7.2 Korisnička podrška

For technical assistance, troubleshooting, or inquiries regarding your APNX V2 ATX Case, please visit the official APNX Store ili njihov službenik webstranica za kontaktne informacije i resurse podrške.