1. Uvod
This manual provides essential instructions for the proper installation, operation, and maintenance of the Protech 61-104025-15 Service Valve. Adhering to these guidelines will ensure safe and efficient performance of the valve. Please read this manual thoroughly before proceeding with any procedures.
2. Proizvod je gotovview
The Protech 61-104025-15 Service Valve is a component designed for various industrial and plumbing applications, particularly within HVAC and refrigeration systems. It facilitates isolation and control of fluid flow, allowing for system servicing without complete depressurization or drainage. This valve is compatible with models such as raka, rakb, ralc, rama, ramb, ramc, ramm, ranc, rand, ranl, rapa, rapb, rapc, rapl, rapm, rara, rarl, rasl, rpka, rpkb, rpla, rplb, rpmb, rpmc, rpmd, rpmm, rpne, rpnk, rpnl, rppb, rppc, rppl, rpql, rprl, saka, sakb, spkb.
Slika 1: The Protech 61-104025-15 Service Valve. This image displays the brass-colored valve body, featuring two 3/4-inch sweat ODF connections on opposing sides and a hexagonal cap at the top for manual operation.
3. Postavljanje i instalacija
Installation of the Protech 61-104025-15 Service Valve requires careful attention to connection types and proper sealing techniques. It is recommended that installation be performed by a qualified technician.
3.1 Pojedinosti povezivanja
- Upper Connection Size: 3/4 inča
- Upper Connection Type: Sweat ODF (Outer Diameter Flare)
- Lower Connection Size: 3/4 inča
- Lower Connection Type: Sweat ODF (Outer Diameter Flare)
3.2 Postupak instalacije
- Sigurnost prije svega: Ensure the system is depressurized and drained before beginning installation. Wear appropriate personal protective equipment (PPE).
- Pripremite veze: Clean the ends of the pipes and the valve's sweat connections thoroughly to remove any dirt, grease, or oxidation. Apply appropriate flux to both surfaces.
- Postavite ventil: Place the valve in the desired position, ensuring proper alignment with the piping.
- Priključci za lemljenje: Using a suitable heat source and solder, create strong, leak-free sweat joints. Allow the joints to cool naturally.
- Ispitivanje nepropusnosti: After installation, pressurize the system and carefully check all connections for leaks using an approved leak detection method.
4. Operacija
The Protech 61-104025-15 Service Valve is designed for straightforward manual operation to control or isolate fluid flow within a system.
4.1 Opening and Closing the Valve
- Do otvoriti the valve, turn the hexagonal cap counter-clockwise until the desired flow is achieved or the valve is fully open.
- Do zatvoriti the valve, turn the hexagonal cap clockwise until the valve is fully closed and flow is stopped. Do not overtighten.
Always operate the valve smoothly and avoid sudden, forceful movements to prevent damage to the valve or system components.
5. Održavanje
Regular maintenance ensures the longevity and reliable performance of your Protech 61-104025-15 Service Valve.
- Periodični pregled: Visually inspect the valve and its connections regularly for any signs of wear, corrosion, or leaks.
- Čišćenje: Keep the exterior of the valve clean. Avoid using harsh chemicals that could damage the valve material.
- Detekcija curenja: Periodically check for leaks around the valve body and connections, especially after any system pressure changes.
- Operativna provjera: Cycle the valve (open and close) periodically to ensure smooth operation and prevent seizing, particularly in systems where the valve remains in one position for extended periods.
6. Rješavanje problema
This section addresses common issues that may arise with the service valve.
6.1 Uobičajeni problemi i rješenja
| Problem | Mogući uzrok | Otopina |
|---|---|---|
| Curenje na spojevima | Improper soldering; damaged pipe or valve connection | Depressurize system, repair or re-solder connection. Replace valve or pipe if damaged. |
| Ventil se teško okreće | Internal corrosion or debris; lack of lubrication | Do not force. Depressurize system and inspect. If internal, valve replacement may be necessary. |
| No flow or restricted flow when open | Valve not fully open; internal obstruction | Ensure valve is fully open. Depressurize system and inspect for internal debris. |
Za probleme koji nisu navedeni ili ako rješenja ne riješe problem, obratite se kvalificiranom servisnom tehničaru.
7. Specifikacije
| Specifikacija | Detalj |
|---|---|
| Marka | ProTech |
| Broj modela | 61-104025-15 |
| Upper Connection Size | 3/4 inča |
| Upper Connection Type | Sweat ODF |
| Lower Connection Size | 3/4 inča |
| Lower Connection Type | Sweat ODF |
| Vanjska završna obrada | Nehrđajući čelik |
| Broj priključaka | 2 |
| Specifikacija ispunjena | ASME B16.34 |
| Težina artikla | 11.2 unci |
| Dimenzije proizvoda (D x Š x V) | 3.8 x 3.2 x 4.3 inča |
| UPC | 662766520378 |
8. Informacije o jamstvu
Unless otherwise noted, all Protech items carry a one-year limited warranty from the date of purchase. Please retain your proof of purchase for warranty claims.
9. Podrška
For technical assistance, replacement parts, or further inquiries regarding the Protech 61-104025-15 Service Valve, please contact a qualified HVAC or plumbing professional. For general product information, you may visit the ProTech trgovina na Amazonu.
