1. Uvod
The AUTOOL HTS558 Walnut Blaster is designed for deep removal of carbon deposits from engine intake manifolds, intake valves, and exhaust valves. This process helps restore engine health by addressing issues such as unstable idling, insufficient fuel combustion, and reduced air-fuel ratio. The machine utilizes walnut sand as a cleaning agent, which is an eco-friendly, non-toxic, and corrosion-preventive material known for its hardness, pressure resistance, and wear resistance.
Figure 1: AUTOOL HTS558 Walnut Blaster main unit and included accessories.
2. Sigurnosne informacije
Always prioritize safety when operating the AUTOOL HTS558. Failure to follow safety guidelines may result in injury or damage to equipment.
- Zaštita očiju: Always wear safety goggles to protect your eyes from walnut sand and carbon debris.
- Zaštita dišnog sustava: Ensure adequate ventilation or wear a respirator to avoid inhaling fine dust particles.
- Tlak zraka: The air pump pressure should be more than 0.7Mpa (7bar/102PSI) for optimal performance.
- Motor isključen: Ensure the engine is completely turned off and cooled before beginning any cleaning procedures.
- Walnut Sand: Use walnut powder with a diameter between 0.4-0.8mm. Avoid exposure to water, as it can cause clumping and nozzle clogging.
- Električna sigurnost: Ensure the machine is properly grounded and all electrical connections are secure before operation.
3. Što je u kutiji
The AUTOOL HTS558 package includes the following components:
- 1x Engine Cleaner Main Unit
- 2x Spray Gun Barrels (long, short)
- 1x Goggles
- 1x Recycle Hose
- 1x Recycle Hose and Spray Gun Connector
- 2x Bags of Walnut Sand (approx. 2kg total)
- 2x Sand Suction Hose Elbows
- 5x Model Adapters
- 1x korisnički priručnik
Figure 2: All components included with the AUTOOL HTS558 Walnut Blaster.
4. Postavljanje
Follow these steps to prepare your AUTOOL HTS558 for operation:
4.1. Install Sand Suction Hose
Connect the sand suction hose to the designated port on the main unit. Ensure a secure fit to prevent leaks during operation.
4.2. Install Sandblasting Gun
Attach the desired spray gun barrel (long or short) to the sandblasting gun. Then, connect the sandblasting gun assembly to the recycle hose and the main unit.
4.3. Add Walnut Media
Remove the top cover of the main unit. Carefully pour the provided walnut sand into the internal container. Ensure the dust filter is properly seated before replacing the cover.
Figure 3: Pouring walnut sand into the machine.
4.4. Connect External Air Source
Connect an external air compressor (not included) to the machine's air inlet. The air pump pressure should be at least 0.7Mpa (7bar/102PSI).
Figure 4: Connecting the external air source to the unit.
4.5. Select and Attach Adapter
Choose the appropriate adapter from the five types provided to match the engine's intake port size. Attach it securely to the end of the sandblasting gun assembly.
Figure 5: Various adapters and their connection to the sandblasting gun.
4.6. Video Guide: Setup
Video 1: Demonstrates the setup process for the AUTOOL Walnut Blaster, including hose connections and media loading.
5. Upute za rad
Perform carbon cleaning using the following procedure:
5.1. Prepare Engine for Cleaning
Turn off the engine. Rotate the crankshaft to ensure the intake valve of the cylinder you are working on is closed. This prevents walnut sand from entering the combustion chamber.
5.2. Insert Nozzle and Begin Cleaning
Insert the sandblasting gun with the appropriate adapter into the engine's intake port. Activate the machine to begin spraying walnut sand. The integrated design allows for simultaneous spraying and recovery of walnut sand and carbon deposits.
Figure 6: Cleaning an engine intake port with the walnut blaster.
5.3. Cleaning Duration
Cleaning time typically ranges between 1-3 minutes per port, depending on the severity of carbon buildup. Monitor the cleaning progress as needed.
5.4. Inspect Results
After cleaning, visually inspect the intake manifold and valves to ensure all carbon deposits have been removed. Repeat the process if necessary.
Figure 7: Before and after cleaning of an intake manifold.
Figure 8: Before and after cleaning of engine intake and exhaust valves.
5.5. Video Guide: Operation
Video 2: Shows the AUTOOL HTS558 in action, demonstrating the carbon cleaning process on an engine.
6. Održavanje
Regular maintenance ensures the longevity and optimal performance of your AUTOOL HTS558.
- Čišćenje filtera za prašinu: The built-in dust filter separates recovered walnut sand from carbon deposits for recycling. Periodically check and clean the filter to maintain efficient operation.
- Upravljanje orahovim pijeskom: Walnut shell grit tends to clump and clog the nozzle when exposed to water. If clumping occurs, shake or blow dry the grit to break up the clumps before use.
- Skladištenje: Store the unit in a dry, clean environment when not in use.
Figure 9: The built-in dust filter for separating walnut sand.
7. Rješavanje problema
If you encounter issues with your AUTOOL HTS558, consider the following common problems and solutions:
| Problem | Mogući uzrok | Otopina |
|---|---|---|
| Insufficient cleaning power | Low air pressure; clogged nozzle; wet walnut sand. | Ensure air compressor provides >0.7Mpa; check and clear nozzle; dry walnut sand. |
| Walnut sand not spraying | Nozzle or hose blockage; insufficient walnut sand; incorrect assembly. | Check all connections and clear blockages; ensure sufficient walnut sand in reservoir; re-assemble according to instructions. |
| Poor suction/recovery | Clogged dust filter; loose hose connection; full collection tank. | Clean or replace dust filter; secure all hose connections; empty collection tank. |
8. Specifikacije
Key technical specifications for the AUTOOL HTS558 Walnut Blaster:
| Značajka | Specifikacija |
|---|---|
| Primjena | All vehicle types |
| Ocijenjeno svtage | 110V/220V |
| Nazivna frekvencija | 50/60HZ |
| Nazivna snaga | 1200 W |
| Kapacitet | 13L |
| Vakuum usisavanje | 0.02Mpa |
| Protok zraka | <300L/Min |
| Dimenzije paketa | 24 x 16 x 16 inches (approx. 400x400x540mm) |
| Težina artikla | 26 pounds (approx. 10KG) |
Figure 10: Detailed specifications and labeled components of the AUTOOL HTS558.
9. Jamstvo i podrška
The AUTOOL HTS558 comes with a 3-year warranty covering damages caused by non-human factors. AUTOOL is committed to providing replacement parts for free within this 3-year period. For any technical support or inquiries, please contact AUTOOL customer service. They aim to respond within 24 hours.
