IDESCO CARDEA T112 RFID Reader

Tehnički podaci

• Product Models: CARDEA T112 / T113, CARDEA PIN T11 / T111, CARDEA W T102 / T103, CARDEA W PIN T10 / T101
• Napajanje: 10-30 VDC
• Potrošnja: 2.5W
• Maksimalna izlazna struja: 500 mA
• Maksimalni ulazni voltage: 30 VDC

Upute za instalaciju

CARDEA

DODATNE INFORMACIJE

WARNINGS AND ADDITIONAL INFORMATION

• The reading distance is affected by the distance between the readers A and the material of the mounting surface, for example, metal reduces the reading distance.
• The maximum output current is 500 mA on both outputs.
• Tamper is a feature that can be enabled by configuration.
• A change in the reader’s position triggers an alarm.
• Bilješka: Tamper activates at each startup and configuration. To prevent false alarms, finish installing before you configure.
• Maksimalni ulazni voltage je 30 VDC.

CONTENTS OF THE READER PACKAGE

• Reader, mounting plate, connector housing cover and connectors.
• Additionally, for wall mounting you will need: screws and a screwdriver.

KONEKTORI I SPOJICE

If you are using Liyy 14 x 0,14 cable, you can connect the wires according to the color coding in the diagram above.

MONTAŽA

Exact dimensions of the products can be found at the end of the next page.

1. Ugradite montažnu ploču
   Montažnu ploču pričvrstite na zid vijcima.
   Bilješka: Nemojte previše zatezati.
2. Wiring the reader
   • Thread cable through the hole in the connector housing cover but do not remove the grommet.
     Use a cable approximately 6mm ±0.5mm thick.
   • Connect wires to connector in correct positions (follow guide on page 2).
     Bilješka: Incorrect wiring can permanently damage a reader.
   • Install connectors to the reader.
   • Press the connector housing cover into place.
3. Attach the reader
   Attaching the reader to the mounting plate with a hinge.
4. Zategnite sigurnosni vijak
   Tighten the security screw from the bottom of the housing.

DIMENZIJE

Cardea

Cardea W

REGULATORNO

This reader complies with the requirements of the EMC Directive 2014/30/EU, the Low Voltage Directive 2014/35/EU, the RoHS Directive 2011/65/EU, the RED Directive 2014/53/ EU and accordingly carries the CE marking.

FCC

Ovaj uređaj je u skladu s dijelom 15 FCC pravila. Rad podliježe sljedeća dva uvjeta:

1. Ovaj uređaj ne smije uzrokovati štetne smetnje.
2. Ovaj uređaj mora prihvatiti sve primljene smetnje, uključujući smetnje koje mogu uzrokovati neželjeni rad.

OPREZ: Sve promjene ili modifikacije koje nije izričito odobrila strana odgovorna za sukladnost mogu poništiti korisnikovo ovlaštenje za rukovanje opremom.

Bilješka: Ova je oprema testirana i utvrđeno je da je u skladu s ograničenjima za digitalne uređaje klase B, u skladu s dijelom 15 FCC pravila. Ova su ograničenja osmišljena kako bi pružila razumnu zaštitu od štetnih smetnji u stambenim instalacijama. Ova oprema generira, koristi i može zračiti radiofrekventnu energiju i, ako se ne instalira i koristi u skladu s uputama, može uzrokovati štetne smetnje radijskim komunikacijama. Međutim, nema jamstva da se smetnje neće pojaviti u određenoj instalaciji. Ako ova oprema uzrokuje štetne smetnje radijskom ili televizijskom prijemu, što se može utvrditi uključivanjem i isključivanjem opreme, korisnik se potiče da pokuša ispraviti smetnje jednom ili više sljedećih mjera:

• Preusmjerite ili premjestite prijemnu antenu.
• Povećajte razmak između opreme i prijemnika.
• Spojite opremu u utičnicu na strujnom krugu različitom od onog na koji je spojen prijemnik.
• Obratite se prodavaču ili iskusnom radio/TV tehničaru za pomoć.

Certifikacija Kanadskog radija

• Ovaj uređaj sadrži odašiljače/prijemnike izuzete od licence koji su u skladu s kanadskim RSS-ovima izuzetim od licence Innovation, Science and Economic Development.
• The minimum installation distance of the product from users is > 20 cm.

Idesco Oy reserves the right to revise this publication and to make changes to its content as well as the right to change or discontinue these products, at any time, without obligation to notify any person or entity of such revisions or changes. All trademarks and registered trademarks are property of their respective owners. 02.07.2025 C00944 v.1.00

Idesco Oy

• Elektroniikkatie 4
• 90590 Oulu
• Finska
• Tel. +358 (0)20 743 4175
• E-mail info@idesco.fi
• idesco.fi

FAQ

What is the purpose of the Tamphm značajka?

Tamper feature can be enabled by configuration and triggers an alarm if there is a change in the reader's position, enhancing security.

What affects the reading distance of the device?

The reading distance is affected by the distance between the readers and the material of the mounting surface. For example, metal surfaces may reduce the reading distance.

What is included in the reader package?

The reader package includes the reader, mounting plate, connector housing cover, connectors, and for wall mounting, screws and a screwdriver are required.

Dokumenti / Resursi

IDESCO CARDEA T112 RFID Reader [pdf] Vodič za instalaciju CARDEA T112, CARDEA T112 RFID Reader, RFID Reader, Reader

Reference

• korisnički priručnik